Turbulent Flow Characteristics Around Bank-Attached Vanes
Volume 17, Issue 4, Winter 2024
https://doi.org/10.22034/iwrj.2023.14436.2538
Sara Ahmadi Adli, Akram Abbaspour, Ali Hosseinzadeh Dalir, Javad Parsa
Abstract Introduction:
Regarding the growing awareness of the environmental issues over the past decades, the main aspect of river engineering has been the environmental improvement of the rivers. River restoration refers to the environmental and ecological aspects of river engineering. New eco-friendly river restoration techniques such as vanes, deflectors, W-weir, U-weir, cross vane and J-hook vanes are generally designed and implemented in accordance with different hydraulic conditions to control the river bed, stabilize the banks, improve the river ecosystem conditions and to overcome the negative effects of the conventional structures on river natural functioning. These structures performance has been evaluated in many studies. Bank-attached vanes are one of the eco-friendly structures. In the present paper, the effect of the different geometry and permeability rates of these structures on turbulent flow pattern has been investigated.
Methods:
Turbulent flows are simulated by solving the Navier-Stokes equations. FLUENT software and large eddy simulation (LES) mathematical model were used to solve the Navier-Stokes equations and simulate the turbulent flow field around bank-attached vanes in a straight channel. Smagorinsky-Lilly subgrid-scale model was used to model unclosed residual stress tensor (τ_ij) in the governing equations. It must be noted that subgrid-scale turbulence models in FLUENT employ the Boussinesq hypothesis to calculate subgrid-scale stresses (τ_kk). To simulate the flow field affected by different bank-attached vanes, boundary conditions, flow depth and approach flow velocity were determined. Streamwise measured and simulated free surface profiles around 30% permeable rectangular vane at different Y/L positions were compared to evaluate the numerical model accuracy. Numerical and experimental results agreed well since relative average error values were 4-5% in all cases. Furthermore, a mesh composed of approximately 150000 elements was considered as an optimum mesh for all created models to resolve flow characteristics. However, due to the different permeability rates, generating the optimum mesh for all cases it is not possible.
Results:
Velocity magnitude results around bank-attached vanes revealed the presence of two flow zones which are the main flow field, upstream and downstream separation region formed due to the local effects of the bank-attached vanes and channel constriction. These zones are separated by a fully turbulent and dynamic flow, named the detached shear layer. In general high velocity zones near the vanes tip region and channel bed effect the local scour hole characteristics, thus tip velocity and maximum velocity variations are investigated at the near bed horizontal plane. Moreover, parameters such as tip velocity, maximum velocity and flow separation angle are affected by the interaction of different eddies, varying geometry and permeability conditions. Results showed that tip velocity and maximum velocity ratios have declining trend with increasing permeability rate. Generally by increasing the permeability rate, bank-attached vanes do not have a significant effect on flow pattern. Bed shear stress is considered as one of the primary parameters that affect the main flow field and downstream separation zone, results showed that due to the local effects of the bank-attached vanes, channel constriction and interaction of the horseshoe vortices downstream of the simulated vanes, maximum bed shear stress values mainly occurred at X⁄L= 2.4 section. Furthermore, by increasing the permeability rate, maximum bed shear stress values shifted towards the channel centerline. In general, due to the triangular vanes cross-sectional opening (geometry), these structures effect on flow characteristics is smaller in comparison to the rectangular vanes.
Study of Velocity over Submerged Rigid Vegetation with random Non-Uniform Height in Open Channels
Volume 17, Issue 4, Winter 2024
https://doi.org/10.22034/iwrj.2023.14516.2554
sima Samadi Gharehverana, akram abbaspour, Davod Farsadizadeh, Ali Hosseinzadeh Dalir
Abstract Abstract
Introduction:
The roughness of the open channels bed and the walls have a great impact on the hydraulic characteristics of the flow, and to perform the best management and control tasks, the change in the behaviour and characteristics of the flow in the presence of these roughness should be known well. Vegetation is one of the most important and common roughness, which have various types and characteristics. One of the most important characteristics is their degree of flexibility, which are usually divided into two general categories: rigid and flexible. From the past until now, researchers are always trying to predict the effect of the presence of vegetation on the flow path and to provide more accurate relationships for predicting different characteristics of the flow, including the flow velocity. The vegetation studied in this research is rigid and inflexible, and to bring the vegetation conditions close to their natural state, its height distribution is considered non-uniform and random.
Methods:
Experiments were carried out using a rectangular flume with a length of 10 m, a width of 0.5 m and a depth of 0.6 m. At the downstream end of the flume, a rectangular weir with an adjustable angle was installed to adjust the flow height inside the channel and the vegetation submergence ratio. Vegetation models used in the experiments include stainless steel cylinders at three heights 3.5, 5 and 7 cm, which are used to simulate hard plant stems. During the experiments, the submergence ratio of the cylinders has been considered variable. The diameter of the cylinders is 5 mm. The distribution of the cylinders is staggered, where the longitudinal and lateral distances are the same, but the height distribution is completely random, and Mathematica software was used to generate random numbers to determine the location of each cylinder. The distance between the cylinders and, as a result, the vegetation density per unit area is variable and in total three different densities were considered for stems. The flow discharge varied between 5 and 60 lit/s and an ultrasonic flowmeter was used to measure it. Velocity measurement started from 4 m from the channel entrance. A 3D ultrasonic velocimeter (ADV) with a frequency of 25 Hz was used to measure the point velocity. The flow is assumed to be uniform and steady for all experiments.
Results:
The distance between the cylinders and, as a result, the vegetation density per unit area is variable and in total three different densities were considered for stems. The flow discharge varied between 5 and 60 lit/s and an ultrasonic flow meter was used to measure it. Velocity measurement started from 4 m from the channel entrance. A 3D ultrasonic velocimeter (ADV) with a frequency of 25 Hz was used to measure the point velocity. The flow is assumed to be uniform and steady for all experiments.
Analytically using the momentum equation in the layers with vegetation and the logarithmic law in the layers without vegetation. The velocity profile is presented in this research, unlike the uniform distribution, has two inflection points whose position depends on the vegetation density. To determine the CD, a special plant Reynolds number (Re*) has been introduced, and as this Reynolds number increases, the drag coefficient decreases. An empirical relationship between CD and the effective parameters is presented. The effect of different dimensionless parameters that were extracted through dimensional analysis, was investigated on the flow velocity and the results show that with the increase in the flow Reynolds and the Froude numbers, the velocity increases in all the flow layers, but the change of these numbers has no effect on the position of the inflection points of the velocity profile. With the increase of the vegetation density, the flow velocity in the vegetation layers and the upper layer decreases and increases, respectively. By increasing the submergence ratio of the cylinders for a constant flow rate, the flow velocity decreases in all three layers, but the effect of the submergence increase on the flow velocity is different for the flow layers, so for example, with a 30% increase in the submergence ratio, the average velocity decrease in the vegetation layer is 10%, however, shows a decrease of 25% in the upper layer. As the results showed, with the change of vegetation conditions, many hydraulic properties of the flow changed, so this field still needs to be discussed. The present study was conducted on hard vegetation that has a random height distribution with regular intervals. In future studies, researchers can study natural vegetation with random intervals and bring their laboratory conditions closer to the conditions of the vegetation distribution in natural riverbeds.
Analytical model for variations of water depth in downstream channel of four-branch junction with subcritical flow
Volume 12, Issue 1, Spring 2018, Pages 73-81
Sayyed Hossein Hosseini, Davood Farsadi Zadeh, Ali Hossein zadeh Dalir, Ali Hossein zadeh Dalir
Abstract
Experimental study of the effect of channel side slope trapezoidal channel over the erosion phenomenon in open-channel confluence
Volume 9, Issue 4, Winter 2016, Pages 119-130
payam khosravinia, Ali Hosseinzadeh Dalir, Mahmud Shafai Bajestan, Davod Farsadizadeh
Abstract Channel-river confluences are an important issue in open channel studies. Variation in quantity and direction of velocity and discharge value causes the erosion of the bed and banks near the confluence. Adequate knowledge about the process of forming a scour hole can be helpful to determine the proper distance of protective structure from channel confluence and river bank. The dynamic of river confluence is as a function of the momentum ratio of reaching flows and the geometry of the channels confluence location. By considering this fact that these conditions do not exist in nature and usually the banks of rivers are included. The slope of the banks causes the changes in three dimensional flow patterns in the place of confluence in relation to septum with 90 degrees that can be the reason of changing the pattern of scouring.
The main objective of this study is to investigate the effect of side slope of the channel on the maximum depth of the erosion at the confluence with a main channel. First by using the dimensional analysis, dimensionless parameters are derived. Then, by building a physical model, the effect of various parameters, including side slope of the channel (Z), discharge ratio (Qr), downstream densimetric Froude number, and downstream Froude number, on the maximum depth of bed erosion (ds) in a perpendicular confluence is investigated. The experimental tests were conducted in a main flume (6 m length, 80 cm width and 50 cm depth), a tributary flume (5 m length, 24 cm width, and 50 cm depth). The bed slope of two channels is considered as horizontal. Changes are made to form the false floor and movable bed, and also the width of the main channel is decreased from 80 to 50 centimeters to enhance the ability of turning the main channel wall to a sloping shape. Main and tributary channels with wooden platform with 14 centimeter height and the width that equal to width of main and tributary channels are raised. The space between these three false floors is connected as experimental region and then is filled with sediment. The side slope of the main channel is considered as 45, 60 75 and 90 degree. For all experiments, the input discharge of the flume was regulated as 15 lit/s. By considering four wall side slopes, four of discharge ratios and four different flow depths, four Froude numbers and four densimetric Froude numbers are applied. To regulate the water surface at the end of main channel, we used stop logs with one centimeter height and by omitting each stop log, one Froude number is produced. The experiment was ended when the equilibrium condition for erosion and scouring hole is created. By considering this fact that the most equilibrium time will take in the slope of 45 degrees in comparison with the other slopes. The experiments with the slope of 45 degrees were done at the most and least of ratio discharge and finally, after six hours, 90 percent of scouring was produced. Therefore, for all the experiments, the experiment time is considered equal to six hours.
Immediately after the experiments are started, because of contacting the tributary and main channel flow, two rounding vortices are made. These vortices moved in contrary to each other. It is the main factor to start the scouring of bed materials in the place of confluence. Rounding vortices that are nearer to the place of confluence, act stronger because of the contraction of flow. The bed material in downstream confluence is shouted to the surface of water and moved to the downstream of the channel. When the discharge ratio is going to be increased, because of the increasing of momentum of tributary channel, the tributary flow enter the main channel with an increasing intensity and this make the vortices and down-flow stronger and causes bed scouring especially in the first stages of the experiment. Bed materials that are shooting to the surface of the flow, after becoming nearer to the water surface, they lose their energy and when they are falling, the secondary flow transported them to the downstream confluence and by settling these particles, we could see little by little sediment bar.
The results indicate that the depth of scour at confluence increases with increasing the side slope of the channel, discharge ratio, densimetric Froude number, and Froude number, whereas it decreases as flow depth increase. The best performance in decreasing scour (equal to 46% in comparison with side slope of 90 degrees) belongs to side slope of 45 degrees and the discharge ratio of 0.2. The derived relationship for predicting the maximum depth of scour at the confluence shows that scour depth is more related to Froude number and downstream densimetric Froude number than the other parameters (i.e. discharge ratio, side slope of the channel and relative depth). The best performance in decreasing the scour was belong to side slope of 45 degrees and the discharge ratio of 0.2 which was equal to 46 percent. Since the side slope of 75 degrees is close to slope with 90 degrees, it doesn't show the appropriate operation, especially in high discharges ratio and it has 9 percent decreasing of scouring. In the present study a dimensionless equation was presented which can be applied for prediction of scour depth at river confluences with the variable side slope.
Study of vortex flow extending around the reservoir sluice gate in order to increase in flushing efficiency
Volume 8, Issue 2, October 2014, Pages 51-62
Hamidreza Jalili, ali Hoseinzade Dalir
Abstract Many of the reservoirs in the world are faced with acute sedimentation problems and in many cases the sedimentation led to closure of the sluice gates and it intensifies accumulation of sediment in these reservoirs. According to international reports, one of the most effective ways to removal of the deposited sediment from large reservoirs is partial Flushing. But this method erodes a small amount of sediment around the sluiceway and it cannot solve the sedimentation problems, completely. In this study, with knowledge about vortex flow around the sluiceway, there vortices were increased by using a specific structure in order to increase partial Flushing. The results show that with using a semi-cylinder structure, the flushing efficiency will increase up to 16.4 times. Therefore, the proposed method can be applied in the large reservoirs and in the reservoirs with serious conditions, for sluicing a significant amount of sediments out of the reservoir, in a short time, with a low loss in water resources.
